LED Dimmer LED-03E-250-DALI

LED Dimmer with 3 independent constant current outputs, CC (constant current) 250mA. Dimming 0-100% high resolution, monochrome coloured or circadian/HCL (Human Centric Lighting warm white/cold white).

The dimmer is controlled via the DALI protocol.

Quick Facts

  • 250mA constant current
  • dimming 0-100%
  • protocol DALI

The LED Dimmer was developed to control up to 3 LED lights 250mA via the DALI protocol.
This makes it possible to control the brightness of the LEDs between 0 and 100% absolutely flicker-free. With 2 DIP switches, the DALI dimmer is preset to the channel operating mode (1-, 2- or 3-channel dimmer) and accordingly only requires the defined number of DALI addresses.

Electrical Data

Operating voltage DALI BUS supply, max. 2mA (total for 1-3 CONTROL GEARS)
12V to 48V DC impulse-proof for Power-LEDs
Current consumption max. 300mA per LED circuit, back-up fuse max. 10A
Output power 3 circuits with 250mA each
BUS control DALI compatible with DALI IEC 62386-102
3 DALI Standard CONTROL GEARS (DEVICE TYPE 0)
PHYSICAL MIN LEVEL = 1
Exceptions:
- no lamp failure detection
- no SYSTEMFAILURE LEVEL "255" only "0-254"
Cable length power supply
to LED dimmer 		max. 40m (observe max. permissible voltage drop for cable cross-section calculation)
Cable length LED dimmer
up to the last LED 		max. 50m (observe max. permissible voltage drop for cable cross-section calculation)
Mounting housing for lamp installation
Connection screw terminals 1.5mm²
Max. ambient temperature +45°C
Storage temperature -25°C to +70°C
Humidity 0...85 % r.h. non-condensing
Protection class in not installed state IP 10

Design, Dimensions, Weight

Design plastic housing for lamp installation
Dimensions LxWxH 140x35x27mm
Weight 80g

Ordering Data and Conformity

Type designation LED-03E-250-DALI
Article no. 80100429
Make ISYnet
Conformity CE

Screen resolution JPG
Print resolution JPG
Print resolution PNG

Instruction Manuals

Wiring Diagrams

DIP switches

DIP-1DIP-2OutputsDALI-GEAR

OFF

OFFCathode 1 (Ka.1)GEAR A
Cathode 2 (Ka.2)GEAR B
Cathode 3 (Ka.3)GEAR C
 
ONOFFCathode 1 (Ka.1)GEAR A
Cathode 2 (Ka.2)GEAR A
Cathode 3 (Ka.3)GEAR A
 
OFFONCathode 1 (Ka.1)GEAR A
Cathode 2 (Ka.2)GEAR A
Cathode 3 (Ka.3)GEAR B
 

ON

ONCathode 1 (Ka.1)GEAR A
Cathode 2 (Ka.2)GEAR B
Cathode 3 (Ka.3)GEAR B
Notice: After changing the DIP switches, the DALI addresses of the LED dimmer must be deleted again. This must then be reparameterized in the current configuration.

State Indicator (Factory Setting)

LEDStateMeaning
redOnDimmer is still in (default) delivery state
OffDimmer is no longer in (default) delivery state, i.e. parameters were changed or dimmer was addressed


Please note:
The red LED is NOT an operating voltage or function indicator of the dimmer! It is located next to the DIP switch.

Parameterisation

  • Dimming curves
    The following dimming curves can be parameterised at the factory:

Pin Assignment

Terminals LED side

+Ub Voltage input + for LED power supply
+Ub Voltage input + for LED power supply
GND Voltage input - for LED power supply
GND Voltage input - for LED power supply
LED (+) Common anode (+) of the Power-LED
LED (+) Common anode (+) of the Power-LED
LED 1 (-) Cathode (-) for Power-LED channel 1
LED 2 (-) Cathode (-) for Power-LED channel 2
LED 3 (-) Cathode (-) for Power-LED channel 3

Terminals BUS side

DALIinternal
connected		DALI BUS connection 1
DALIDALI BUS connection 1
DALIinternal
connected		DALI BUS connection 2
DALIDALI BUS connection 2

Additional Equipment

Article no.: 80100604 ISYnet - NT-LED-12V-15A Power supply for LED applications
Article no.: 80100608 ISYnet - NT-LED-48V-5A Power supply for LED applications
Article no.: 80100609 ISYnet - NT-LED-48V-5,4A Power supply for LED applications
Article no.: 80100610 ISYnet - NT-LED-48V-10A Power supply for LED applications
Article no.: 80100611 ISYnet - NT-LED-48V-20A Power supply for LED applications
Article no.: 80100616 ISYnet - NT-LED-24V-5A Power supply for LED applications
Article no.: 80100618 ISYnet - NT-LED-24V-10A Power supply for LED applications
Article no.: 80100619 ISYnet - NT-LED-24V-10A Power supply for LED applications
Article no.: 80100620 ISYnet - NT-LED-24V-20A Power supply for LED applications
Article no.: 80100640 ISYnet - NT24V/40A-3Ph Power supply for LED applications
Article no.: 80100641 ISYnet - NT-LED-24V-40A Power supply for LED applications

Request

LED-03E-250-DALI_bild72.jpg

LED-03E-250-DALI

Article no.: 80100429

LED Dimmer with 3 independent constant current outputs, CC (constant current) 250mA. Dimming 0-100% high resolution.
+ shipping costs
  • kostenlose Anfrage / free request
    from 1 € 0.00 € 0.00
  • Click & Collect
    from 1 € 0.00 € 0.00
    Local pick-up
  • DHL
    from 1 € 0.00 € 5.90 Incl. 20.00% VAT
    Delivery within three days
  • DHL Express
    from 1 € 0.00 € 11.90 Incl. 20.00% VAT
    Delivery on the next day
  • Fedex
    from 1 € 0.00 € 6.90 Incl. 20.00% VAT
    Delivery within three days
  • TNT
    from 1 € 0.00 € 8.90 Incl. 20.00% VAT
    Delivery within three days

This website uses cookies

We use cookies to personalise content and ads, provide social media features and analyse traffic to our website. We also share information about your use of our website with our social media, advertising and analytics partners. Our partners may combine this information with other data that you have provided to them or that they have collected in the course of your use of the Services. You give consent to our cookies when you continue to use our website.

Get more info about used cookies
Cookie optin by Olli machts